Fostex FD-4 User Manual Page 85
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
85
Changing the Initial setting (SETUP mode)
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
S
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
S
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
Setting the Metronome function
“Setting the Metronome function” menu allows you to de-
termine whether or not the FD-4 outputs a metronome
sound from Real track 4 during playback or recording.
Turning the Metronome function on enables you to record
your performance while playing the instrument accompa-
nying the metronome sound.
Setting a preroll value
The FD-4 features the Preroll function that enables you to
locate a position a few seconds prior to a specified locate
point. The “Setting a preroll value” menu allows you to set
the preroll time (in seconds).
The Preroll function is convenient when you wish to moni-
tor the audio data from a point slightly before the locate
point.
• Initial setting: 00 second
• Setting range of preroll time: 00-10 seconds in one second steps
* You can set the value for each Program individually.
* The settings can be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the unit.
<Note>
Since Real track 4 outputs the metronome sound when this function
is turned on, you cannot play the audio recorded on this track. Also,
do not record any data on track 4.
The FD-4 can output the metronome sound even from an unre-
corded area (outside of the range from ABS 0 to ABS REC END) on
track 4.
• Initial setting: oFF
• Option: oFF, on
* You can turn the function on and off for each Program individually.
* The settings can be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the unit.
Setting the Metronome function
1.While the FD-4 is stopped, press the SETUP key to enter
SETUP mode.
2. Turn the JOG dial to select [Click
?] (? flashes.), then press
the EXECUTE/YES key.
The current setting (oFF or on) appears on the display.
Pressing the EXECUTE/YES key lights up the flashing [?]
character steadily; the current setting flashes. The initial
setting is [oFF] as shown below.
3.Turn the JOG dial to select on or oFF.
Selecting [on] will enable the output of the metronome
sound. Selecting [oFF] (initial setting) will disable the
metronome output.
4.Press the EXECUTE/YES key.
The display shows the selection (on or oFF), then returns
to the indication in step 2.
To cancel the setting operation, or to restore a setting obtained prior
to the EXECUTE/YES key press, press the STOP button or the
EXIT/NO key. Each time you press one of these keys, the FD-4
returns to the previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
Setting a preroll time
1.While the FD-4 is stopped, press the SETUP key to enter
SETUP mode.
2. Turn the JOG dial to select [Preroll ?] (? flashes.), then press
the EXECUTE/YES key.
The current preroll time setting appears on the display.
Pressing the EXECUTE/YES key lights up the flashing [?]
character steadily; the current setting flashes. The initial
setting is [00] as shown below.
This point is actually located.
Locate point (stored in the
memory key)
This point is located if the
current position is before
the locate point.
This point is located if the cur-
rent position is after the locate
point.
Preroll time (before the locate point)
can be set between 00 and 10 sec-
onds.
3.Turn the JOG dial to enter a desired preroll time value.
You can set a value in one-second increments. Rotating
the JOG dial clockwise increases the value, and rotating it
counter-clockwise decreases the value.
4.Press the EXECUTE/YES key.
The display shows the value, then returns to the
indication that appeared in step 2.
To cancel the setting operation, or to restore the setting obtained prior to
the EXECUTE/YES key press, press the STOP button or the EXIT/NO
key. Each time you press one of these keys, the FD-4 returns to the
previous hierarchy level of the menu, and finally exits SETUP mode and
displays the previous Time Base.
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Introduction 4
- Main features 4
- Recording Preparation 5
- 2. Press the EXECUTE/YES key 6
- <Note 1> 7
- <Note 2> 7
- <Note 3> 7
- <Note 4> 7
- <Note 5> 7
- Flashing 8
- Names and Functions 9
- Names and Functions 12
- 13. Record track select keys 12
- 15. Contrast adjustment knob 12
- EJECT 13
- SHUTTLE 13
- AUTO PUNCH 14
- P.EDIT 15
- LOC MEM 15
- PREVIEW 16
- 1.Input jacks [1, 2, 3, 4] 18
- 2.Headphone jack [PHONES] 18
- Pin 1: GND 19
- Pin 2: HOT 19
- Pin 3: COLD 19
- Display Section 20
- Preset display 21
- TIME BASE SEL key 21
- The REMAIN display 22
- Warning messages 23
- Before Starting 24
- Recording method 25
- REMAIN indicator 25
- Input monitoring 26
- Playback monitoring 26
- PAN knobs and stereo bus 27
- Basic Recording and Playback 28
- Undo/Redo recording 30
- (LOCATE ABS 0) 31
- Basic Multitrack Recording 32
- Undo/redo overdubbing 33
- Mixdown 34
- Effect unit 1 35
- Effect unit 2 35
- Master Recorder 35
- Handling Programs 36
- <Important!> 37
- 3.Press the EXECUTE/YES key 38
- AUTO A.PUNCH 39
- SYNC OUT 39
- Playback in Vari Pitch Mode 40
- If the microphone has a bal 41
- INPUT 3 (XLR) jack on the 41
- Punch In/Out Recording 43
- Auto Punch In/Out Take 45
- • Initialize the FD-4 46
- Manual Punch In/Out take 47
- 4.Press the STOP button 48
- Ping-Pong Recording 49
- Quitting ping-pong recording 50
- Digital Recording 52
- Selecting a Program to record 53
- Digital mixdown 54
- CORDER IN jack 55
- Editing Tracks 56
- Undo/Redo Paste 58
- Real track 59
- Track Exchange 60
- Cue & Review Function 62
- memory keys 63
- Storing in real-time 63
- Editing and storing data 64
- Locate Function 66
- Auto Return 67
- Auto Repeat 68
- Preview Function 69
- MIDI Synchronization 71
- Connecting an external device 72
- Setting MIDI SYNC OUT 72
- Computer 73
- Sync system in Slave mode 74
- Recording 75
- <Note> 75
- Saving and Loading Song Data 76
- Preparing a DAT machine 77
- Operation on the FD-4 77
- Changing the Initial Settings 81
- Setting a time signature 82
- Setting a tempo 83
- Setting a preroll value 85
- Setting MIDI sync signal 86
- Setting an MTC frame rate 87
- Setting an MTC offset value 87
- Setting Offset mode 88
- Setting the Slave mode 88
- Setting the Slave type 89
- Recording enabled/disabled 90
- Setting digital input tracks 91
- Setting digital output tracks 92
- Setting the MIDI device ID 93
- MMC Command List 95
- Inquiry Message List 95
- Cleaning the exterior 96
- Block Diagram 97
- * General 97
- Declaration of EC Directive 98
- FOSTEX CORPORATION 100
- FOSTEX CORPORATION OF AMERICA 100
Related products and manuals for Digital pianos Fostex FD-4
Digital pianos Fostex VF08 User Manual
(118 pages)
(118 pages)
Digital pianos Fostex FD-8 User Manual
(121 pages)
(121 pages)
Digital pianos Fostex VF160EX User Manual
(158 pages)
(158 pages)
© 2020, manymanuals.com. All rights reserved. | 2.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals