Fostex FD-4 User Manual Page 93
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
93
Changing the Initial setting (SETUP mode)
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
3.Use the JOG dial to turn the mode on or off.
When you turn the JOG dial clockwise and counter-clock
wise, [on] and [oFF] flash alternately.
Selecting [on] turns BAR/BEAT resolution mode on, and
selecting [oFF] turns BAR/BEAT resolution mode off.
4.Press the EXECUTE/YES key.
The selected mode setting is stored, and “?” flashes.
To cancel the operation, or to restore the setting obtained prior to
the EXECUTE/YES key press, press the STOP button or the EXIT/
NO key. Each time you press one of these keys, the FD-4 returns to
the previous hierarchy level of the menu, and finally exits SETUP
mode and displays the previous Time Base.
Setting the MIDI device number
The “Setting the MIDI device number” menu enables you
to set the FD-4 device ID number required to control the
unit from a sequence software using MMC (MIDI Machine
Control) or FEX (Fostex System Exclusive Message).
The transmit device ID links to this setting.
You can set the device ID from 00 to 99.
However, if the device ID number of the message the FD-4
receives is [7F], the FD-4 will recognizes it to perform the
corresponding operation, regardless of its device ID set-
ting.
• Initial setting: 00
• Device ID: 00–99
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the unit.
Setting the MIDI device ID
1.While the FD-4 is stopped, press the SETUP key to enter
SETUP mode.
2.Turn the JOG dial to select [Device ID?] (“?” flashes), then
press the EXECUTE/YES key.
The current MIDI device ID number appears on the
display.
Pressing the EXECUTE/YES key turns off the flashing [?]
character, and the MIDI device ID number flashes.
With the initial setting, [00] flashes as shown below.
3.Use the JOG dial to set the desired MIDI device ID number.
Turning the JOG dial clockwise increments the value, and
turning it counter-clockwise decrements the value.
4.Press the EXECUTE/YES key.
The MIDI device ID number is stored, and “?” flashes.
To cancel the operation, or to restore the setting obtained prior to
the EXECUTE/YES key press, press the STOP button or the EXIT/
NO key. Each time you press one of these keys, the FD-4 returns to
the previous hierarchy level of the menu, and finally exits SETUP
mode and displays the previous Time Base.
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Introduction 4
- Main features 4
- Recording Preparation 5
- 2. Press the EXECUTE/YES key 6
- <Note 1> 7
- <Note 2> 7
- <Note 3> 7
- <Note 4> 7
- <Note 5> 7
- Flashing 8
- Names and Functions 9
- Names and Functions 12
- 13. Record track select keys 12
- 15. Contrast adjustment knob 12
- EJECT 13
- SHUTTLE 13
- AUTO PUNCH 14
- P.EDIT 15
- LOC MEM 15
- PREVIEW 16
- 1.Input jacks [1, 2, 3, 4] 18
- 2.Headphone jack [PHONES] 18
- Pin 1: GND 19
- Pin 2: HOT 19
- Pin 3: COLD 19
- Display Section 20
- Preset display 21
- TIME BASE SEL key 21
- The REMAIN display 22
- Warning messages 23
- Before Starting 24
- Recording method 25
- REMAIN indicator 25
- Input monitoring 26
- Playback monitoring 26
- PAN knobs and stereo bus 27
- Basic Recording and Playback 28
- Undo/Redo recording 30
- (LOCATE ABS 0) 31
- Basic Multitrack Recording 32
- Undo/redo overdubbing 33
- Mixdown 34
- Effect unit 1 35
- Effect unit 2 35
- Master Recorder 35
- Handling Programs 36
- <Important!> 37
- 3.Press the EXECUTE/YES key 38
- AUTO A.PUNCH 39
- SYNC OUT 39
- Playback in Vari Pitch Mode 40
- If the microphone has a bal 41
- INPUT 3 (XLR) jack on the 41
- Punch In/Out Recording 43
- Auto Punch In/Out Take 45
- • Initialize the FD-4 46
- Manual Punch In/Out take 47
- 4.Press the STOP button 48
- Ping-Pong Recording 49
- Quitting ping-pong recording 50
- Digital Recording 52
- Selecting a Program to record 53
- Digital mixdown 54
- CORDER IN jack 55
- Editing Tracks 56
- Undo/Redo Paste 58
- Real track 59
- Track Exchange 60
- Cue & Review Function 62
- memory keys 63
- Storing in real-time 63
- Editing and storing data 64
- Locate Function 66
- Auto Return 67
- Auto Repeat 68
- Preview Function 69
- MIDI Synchronization 71
- Connecting an external device 72
- Setting MIDI SYNC OUT 72
- Computer 73
- Sync system in Slave mode 74
- Recording 75
- <Note> 75
- Saving and Loading Song Data 76
- Preparing a DAT machine 77
- Operation on the FD-4 77
- Changing the Initial Settings 81
- Setting a time signature 82
- Setting a tempo 83
- Setting a preroll value 85
- Setting MIDI sync signal 86
- Setting an MTC frame rate 87
- Setting an MTC offset value 87
- Setting Offset mode 88
- Setting the Slave mode 88
- Setting the Slave type 89
- Recording enabled/disabled 90
- Setting digital input tracks 91
- Setting digital output tracks 92
- Setting the MIDI device ID 93
- MMC Command List 95
- Inquiry Message List 95
- Cleaning the exterior 96
- Block Diagram 97
- * General 97
- Declaration of EC Directive 98
- FOSTEX CORPORATION 100
- FOSTEX CORPORATION OF AMERICA 100
Related products and manuals for Digital pianos Fostex FD-4
Digital pianos Fostex VF08 User Manual
(118 pages)
(118 pages)
Digital pianos Fostex FD-8 User Manual
(121 pages)
(121 pages)
Digital pianos Fostex VF160EX User Manual
(158 pages)
(158 pages)
© 2020, manymanuals.com. All rights reserved. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals