Fostex VF160EX User Manual download pdf (Page 50)

Flashing

Lighting

You can edit the various parameter settings such as pan and equalizers for channels 1 through 16 and the master

channel. We refer this type of editing as "Channel parameter edit". There are several channel parameter edit keys on

the top panel (as shown below) and pressing the dedicated key for the parameter you want to edit brings up the

corresponding edit screen. Some keys also handle the second parameter (labeled under the key) and you can bring

up the corresponding edit screen by pressing the key while holding down the [SHIFT] key. You can view and/or edit

the following parameters.

• Pan setting

• 3-band equalizer setting

• Effect send level setting

• Pre/post selection of the effect send

• Aux (auxiliary) send level setting

• Pre/post selection of the Aux (auxiliary) send

• Compressor setting

• Fader level setting

• Channel view (viewing only)

<Hints>

If a channel whose source is set to INPUT via the IN-

PUT SEL setting is selected as the edit channel, the

channel name is shown as below.

In the following example, channel 9 which is set to

INPUT, is selected as the edit channel.

Adjusting Pan

You can adjust the pan (or balance) of each input chan-

nel signal fed to the stereo outputs, as well as fed to the

Rec buss outputs. The panpot for master channel con-

trols the L/R level balance of the stereo outputs.

1. Press the [PAN] key.

All channel settings are shown on the screen.

The first time you bring up the channel parameter edit

screen, the message prompting to select a channel ("Select

CH!") flashes, as well as all the CH STATUS/CH SEL

indicators on the panel flash.

From the second time on, the previously selected channel

is selected and ready to be edited when bringing up the

screen (as shown in the drawing of step 2 below).

2. Press the [CH STATUS/CH SEL] key of the desired

channel.

The current settings are shown, together with the selected

channel name. The icon for the selected channel is flash-

ing, indicating that you can edit it.

3. Use the [JOG] dial to adjust panning.

Rotating the [JOG] dial to the left or right moves the pan

position to the left or right respectively.

The following show examples of the pan settings.

Pan position:

center

Pan position:

hard left

Pan position:

hard right

•Controllable channels

Channels 1 through 16 and the master channel

•Available values

L10 (hard left) through C (center) to R10 (hard

right) (the default setting: "C" for all channels)

* Values are displayed between L10 and R10 in 21

steps but the actual pan setting is changed smoothly

and continuously as rotating the [JOG] dial.

4. To set another channel's pan, repeat steps 2 and 3 above.

5. After completing pan editing, press the [EXIT/NO] key.

The VF160EX exits the channel edit mode and the display

returns to the Normal display.

Channel Parameter Edit

If you must edit channel param-

eters such as setup of PAN or EQ,

be sure to check that the "

Scene

Sequence Mode

", explained later,

is switched "

Off"

. Should the pa-

rameters be edited with this

Scene Sequence Mode

" switched

", the parameters will be re-

turned to their original setting

when VF160EX is operated in

PLAY or STOP. Refer to page

for "

On/off of the Scene Sequence

Mode

CH PARAM EDIT

CH VIEWFADER

LO-G

PAN

PRE/POST

MID-G/F/Q

AUX1/AUX2

COMPPRE/POST

EFF1/EFF2

HI-G/F/Q

EQ/COMP

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 157 158

Comments to this Manuals

No comments

Fostex VF160EX User Manual Page 50

Comments to this Manuals